Product List

---

 Tx-2.0 Entry level handset with Forward-Reverse control, plus 3 function buttons. Ideal for basic electrically powered models.

 Tx-2.1 Handset with Forward-Reverse and Inertia control, plus 3 function buttons.  Ideal for basic electrically powered models with worm drive gearboxes.

 Tx-2.2 Handset with Forward-Reverse, Inertia control and reverser switch, plus 3 function buttons. Great if you prefer a reverser and finer regulator control for your electrically powered models.
 

 Tx-3.0 Handset for servo operation, with brilliant calibration facilities. Ideal for live steam locos. 4 Channels: 2 fully proportional with control knobs, 1 reverser function with mid point, and 1 full travel actuator which can be used for a steam whistle, drain cocks or similar on/off function. See videos in LINKS section.

 Tx-3.1 Handset replacement of regular r/c systems for example on Roundhouse diesel outline locos. 4 Channels: 1 fully proportional zero-to-full channel with small control knob, 1 fully proportional channel with centre-off position, for electronic speed controller operation. 1 two-way channel with mid-point, ideal for operating two-way switcher units, and 1 auxiliary channel with single on-off function. Can also be used for live steam.

 Tx-4.0 Handset with Forward-Reverse control, plus 12 functions, for use with models with DCC decoders, or analogue DC models with more than three functions when using Fosworks MCS function expander units. See below.

 Tx-4.1 Handset with Forward-Reverse and Inertia control, plus 12 functions, for use with models with DCC decoders, or multifunction DC models using Fosworks MCS units. 

 Tx-4.2 Handset with full range regulator control and reverser switch, plus 12 functions, for use with models with DCC decoders, or multifunction DC models using Fosworks MCS units. 

 Tx-4.3 Handset, as the Tx-4.1 but with SelectoR switch for simultaneous control of up to 3 models with DCC decoders, or multifunction DC models using Fosworks MCS units. 

 Tx-4.10R Handset, as the Tx-4.2 but with SelectoR for simultaneous control of up to 10 models with full range regulator control, reversing switch with off position and 12 functions. For DCC and DC electrically powered models. 

 Tx-4.30 Handset, as the Tx-4.0 but with three way Channel SelectoR switch and 10 loco SelectoR giving simultaneous control of up to 30 models with E-stop function, forward and reverse control and 12 auxiliary functions. For DCC or DC electrically powered models.

 FRx-22 Receiver for analogue DC electric models. Has 3 function switches plus serial data output for MCS units which can provide up to 8 additional functions. Also has telemetry input for low battery warning unit. Available with horizontal or vertical pins. (Horizontal pins illustrated) Optional long aerial £2  Size: 44 x 19 x 9.5mm 

 FRx23 Receiver. Has 4 servo channels. Can be used for live steam or DC electric models. Also has telemetry input for feedback from model to handset. With horizontal or vertical pins.(Horizontal pins illustrated) Optional long aerial  £2  (125mm with 32mm tip aerial) Size: 44 x 19 x 9.5mm 

 FRx24-2A receiver combined with 2 amp DCC interface module to operate DCC decoders. 12-28v input For use with OMNI Tx4 series transmitters. Optional long aerial £2

 Size: 52 x 21 x 19mm Can be supplied slim and long - please contact us for details

FRx24 receiver combined with 5 amp DCC interface module. For use with OMNI Tx-4 series transmitters. Includes DCC interface module. With horizontal pins. Optional long aerial (£2 Extra).  Size: same as 2A

FRx24 receiver combined with 7 amp DCC interface module. For use with OMNI Tx-4 series transmitters. Includes DCC interface module. With horizontal pins. Optional long aerial (£2 Extra) Size: 52x21x19 plus 46x28x12 with flexible connection.

 ER-2 Manual Speed Controller. 6-16v.

24v version available for £17 Supplied by MFA-Como.

 Cobra High Frequency Electronic Speed Controller. 6-28v. 30W. 44x22x11mm. Perfect for all brushed DC motors including coreless. Has great features including 3 power curves, programmable inertia and zero detection to avoid model runaway when switched on. See instructions for full details.  

 Cobra High Frequency Electronic Speed Controller. 3.7-12v. 30W. 44x22x11mm. Perfect for all brushed DC motors including coreless. The lower voltage range is ideal for models with 4 cell battery packs.  Has great features including 3 power curves, programmable inertia and zero detection to avoid model runaway when switched on. See instructions for full details. 

 Cobra High Frequency Electronic Speed Controller wired ready for sound cards. 6-28v. 30W. 44x22x11mm. Perfect for all brushed DC motors including coreless. Has great features including 3 power curves, programmable inertia and zero detection to avoid model runaway when switched on. See instructions for full details.

 Manual speed controller fully wired with reversing switch and charging loom, in our Plug and Play format with JST connectors.

 Cobra High Frequency Electronic Speed Controller. 6-28v. 100W. 53x26x14mm. Perfect for all brushed DC motors including coreless. 

 Provides 3 auxiliary functions and directional lighting from the Rx22 Data channel. 28 x 16 x 11 mm. 

 Provides 5 auxiliary functions from the Rx22 Data channel. 28 x 16 x 11 mm. 

 Switcher Unit. 2 way, latching-momentary. (Lights & sound cards). For standard r/c systems. Not needed with OMNI.

 Servo. Standard Hitec Servo 3kg cm torque 40x36.5x20mm. 

 Servo. Hitec HS-65HB 1.8kg cm torque. Karbonite gears 24x23x12mm. 

 
Servo. Hitec HS-82MG 3.00kg cm Metal gears 29.7x29.5x12mm. 

 
Hitec HS-65 Servo Bracket for horizontal and vertical mounting of two servos or can be split and used seperately. With M2 mounting screws.

 
Hitec HS-82 Servo Bracket for horizontal and vertical mounting of two servos or can be split and used seperately. With M2 mounting screws.

400mm  Servo extension lead .

100mm Servo extension lead.

 Servo Y splitter lead 100mm. Run two servos from one channel. 

 Pack of 4 red 3mm LEDs with resistors fitted, suitable for up to 24v. 

 Pack of 6 warm white 3mm LEDs with resistors fitted, suitable for up to 24v. Ideal for diesel loco/unit marker lights

 No.1 Wiring loom. Charging socket & Slide Switch with best quality flexible silicon leads and JST connectors.

 Shortened No.1 Wiring loom. Charging socket, Slide switch & Futaba connector for connection to receiver. For use on models with servos, such as live steam. 

 No.1 Wiring loom. Charging socket & Mini Toggle Switch with best quality flexible silicon leads and JST connectors.

 Shortened No.1 Wiring loom. Charging socket, Mini Toggle Switch, & Futaba connector for connection to receiver. For use on models with servos, such as live steam. 

 No.1 Wiring loom. Charging socket & Sub Mini Toggle with best quality flexible silicon leads and JST connectors.

 No.2 Wiring loom. Charging socket, slide switch & LED indicator. For mounting in control panels as provided in our r/c kits.

 JST-BEC Motor plug wire with heat shrink sleeves and interference suppressor. Blue and yellow best quality flexible silicon leads

 JST-BEC Male & Female red connector plugs with best quality flexible silicon leads. 100mm length. 1 pair. 

 JST-BEC Male & Female red connector plugs with best quality flexible silicon leads. 150mm length. 1 pair. 

 JST-BEC Male connector plug with silicon wire. 100mm length. (Gives power) 

 JST-BEC Male connector plug with silicon wire. 150mm length. (Gives power) 

 JST-BEC Male plug with silicon wire and 5A fuse. (Battery lead) 

 JST-BEC Female connector plug & wires. 100mm length. (Receives power) 

 JST-BEC Female connector plug & wires. 150mm length. (Receives power) 

 JST-BEC Male & female BCV leads reinforced tender to engine 

 JST-BEC Male BCV lead (Tender) Black reinforced. 

 JST-BEC Female BCV lead (engine) Black reinforced.

 JST Micro Male and Female plugs with leads. Ideal for use in small models where the red JSTs are too bulky.

 JST Micro Male plug with leads. 

 JST Micro Female plug with leads.

 JST-BEC Female connector plug, connected by wires to a two-way terminal block. 100mm length. Ideal for motors which are already wired to avoid soldering

 Wiring interface for NEM 652 DCC decoder with speaker terminals. 

 Smart Charger 2-12. 2.4v to 14.4v charger. Indicator lights. Fast, automatic charger which bulk charges at 500mA then switches to trickle charge. Not recommended for AAA cells. 

 Smart charger 12-20. 14.4v to 24v battery charger. Indicator lights. Fast, automatic charger for higher voltage packs, not recommended for AAA cells. 

 Cell Checker. Plugs into charging socket and shows battery voltage. 

 Recovery charger. Bring flat NiMH rechargeable battery packs back to life. Suitable for all packs from 2.4V to 24V

 12v Power Supply for track side sound equipment. 

 Universal charger for all NiMH battery packs from 2 to 16 cells (2.4v - 19.2v), complete with voltage display showing status of the battery. This is not a fast charger, nor is it automatic, but it does allow you to take the best care of your battery packs. You can set the charge current to suit the battery - even for AAA size cells - and you can fully monitor the charging process and diagnose battery problems.

 AAA Custom made pack NiMH, with good quality, low self discharge cells - per cell. Includes fuse and JST connector. 

 AA Custom made pack NiMH, with good quality, low self discharge cells - per cell. Includes fuse and JST connector.
 

 Sub-C Custom made pack NiMH, with good quality, low self discharge cells - per cell. Includes fuse and JST connector. 

 ESU-Loksound v5 DCC decoder with sound project of your choice. 8 pin NEM-652 with speaker plug. Use with PNP-510 interface board.

 ESU-Loksound v5L DCC decoder with sound project of your choice and pre-wired with leads necessary for your project.

 
ESU-Loksound v5 XL DCC decoder with sound project of your choice.

 MP3 playback module. Play back any of 9 MP3 tracks from the function buttons on your handset. Tracks can be loaded onto the supplied micro SD card from your computer. 

 MP3 playback module. Play MP3 track from micro SD Card supplied. Create a sound file on your computer and use it on your model. Super slim, only 39 x 23 x 6 mm

Mylocosound Universal Steam Sound card 6-24v. Six auxiliary sounds - Whistle, Bell, Guards Whistle, Safety Valve release, Westinghouse pump and injector.

Mylocosound Universal Diesel Sound card 6-24v. Five auxiliary sounds - Horn 1, Horn 2, Guards Whistle, Brake release, Engine stop/start.

Mylocosound Universal Electric Sound card 6-24v. Five auxiliary sounds - Horn1, Horn2 or air whistle, conductors buzzer, 

MLS Light Diesel Sound card 6-24v. Five auxiliary sounds

Mylocosound Tram and streetcar soundcard with electric motor sounds, horns, whistles, bells and conductors buzzer. Optional rail squeal and brake sounds. Size: 55 x 33 x 11 mm

Mylocosound Railbus sound card with 5 selectable engine sounds, start-up, shut-down, gear change, 6 horns inc. Klaxon, bell, guards whistle and brake squeal. Size: 55 x 33 x 11

Remote control for above USCs to set up and also activate sounds

Switcher Unit. 2 way. To sound whistles and horns etc. where standard r/c servo receiver is being used. Allows each channel to be independently set as a momentary or latching function. (Switches to system ground, not volt free)

Push switch & wires. To manually sound whistle and horn.

Reed switch & magnet. To set off whistles and horns on soundcards or for Autoshuttle operation.

Three way auxiliary cable for FRx-22 to sound card.

Single relay board to connect to FRx-22 receiver, giving one volt free contact pair to operate auxiliary functions on proprietory sound cards such as Phoenix, Piko etc. Can be used for other functions with 2A max current draw. Dimensions: 18x18x9 mm.

Twin relay board to connect to FRx-22 receiver, giving two volt free contact pairs to operate auxiliary functions on proprietory sound cards such as Phoenix, Piko etc.

Can be used for other functions with 2A max current draw. Dimensions: 30x18x9 mm.

Triple relay board to connect to FRx-22 receiver, giving three volt free contact pairs to operate auxiliary functions on proprietory sound cards such as Phoenix, Piko etc.

Can be used for other functions with 2A max current draw. Dimensions: 43x18x9 mm.

Speaker by Alan Butcher. 50mm Dia. 9mm deep.

SND-520 speaker as above, mounted in a resin enclosure. 50mm Dia. 19mm deep.

SND-520 speaker as above, mounted in under-cab-roof enclosure - great sound

Speaker. 40mm Dia. 10mm deep. 8 Ohm 0.25W. Small.

Laptop speaker. 41x21x9mm. Small, mounted in rectangular enclosure. 4 or 8 ohms.

Micro speaker in sound box. 22x17mm x 10mm deep with micro jst.

Speaker, the best of its type - German Visaton 50mm Dia 17mm deep 3W. 8 Ohm.

DCC quality Visaton compact speaker. 50mm x 25.4mm. 10W 4 Ohm

Most impressive quality German made Visaton speaker. 66.5 x 66.5mm 37mm deep. 8 Ohm 8W.

Most impressive quality German made Visaton speaker. 66.5 x 66.5mm 37mm deep. 4 Ohm 8W.

Visaton quality replacement for Aristo class 66 with DCC. 4 Ohm.

Small super bass speaker. 31.1 x 28.1 x 14.8mm. 8 Ohm 3W.

Large Superbass speaker 51 x 51 x 40 mm 4 Ohm 3W, ideal for 0 gauge if you can fit it in.

Toggle Switch - our popular miniature SPST toggle with metal case.

Toggle Switch - miniature DPDT toggle with metal case.

Slide Switch - ideal where a toggle would be too prominent.

Charging Socket - our standard 5.5mm by 2.1mm socket to match chargers.

F5A 5mm x 20mm glass fuse, 5A fast blow.

F3.15A 5mm x 20mm glass fuse, 3.15A fast blow.

LocoSaver Electronic Water Gauge with one probe.

R/C LocoSaver Electronic Water Gauge with one probe.

LocoSaver FosBush for retro fitting probe to existing boiler - specially designed expanding bush, no silver soldering required.

LocoSaver. 1/4" to 1/8" ME 40 probe adaptor bush.

Genuine Halletts SCO460C steam oil in dispensing bottle.

Resin Coal Load for Gauge 1 14xx locos.

Resin Coal Load for Gauge 1 45xx locos.

Resin Coal Load for Gauge 1 57xx locos.

Resin Coal Load for Gauge 1 61xx locos.

Resin Coal Load for Gauge 1 4MT locos

Resin Coal Load for Gauge 1 Terrier locos.

FosMotor 30. Nose hung 12v with 30mm Dia G1MRA steel wheels.

FosMotor 34. Nose hung 12v with 34mm Dia G1MRA steel wheels.

FosMotor CW. Nose hung 12v with customer wheels.

30mm Dia pair of G1MRA standard steel wheels with solid axle (1 wheelset)

34mm Dia pair of G1MRA standard steel wheels with solid axle (1 wheelset).

Ball bearings.

Flange bearing.